While I was emplode over the ethernet, the player stopped working. (Download indicator hasn't moved) So I had to power off.
Now everytime I try to use emplode I get the error message: the download process failed during stage 2: Error 0xfffffff8.(For USB, serial and ethernet)
I uploaded the consumer and the developer image several time. But it still doesn't work. Any ideas?

At the moment there is no music on the player. When I reboot the player it say's End of playlist.

Is there a tool, which erase everything on the hole disc, including partition and then creates it as if the player was new?

Thanks
Rene

Here is the output from the serial line:
empeg-car bootstrap v1.00 20000601 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!
Copying kernel...
Calling linux kernel...
Uncompressing Linux........................
mpeg-car player (hardware revision 7, serial number 80000251)
Command line: mem=12m temp=47
Calibrating delay loop... 207.67 BogoMIPS
Memory: 11000k/12M available (968k code, 20k reserved, 292k data, 8k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
empeg display initialised.
empeg dspaudio driver initialized
empeg audio-in initialised, CS4231A revision a0
empeg infra-red support initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004900).
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IBM-DARA-218000, ATA DISK drive
hda: IBM-DARA-218000, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IBM-DARA-218000, 17301MB w/418kB Cache, CHS=35152/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:10:00:f
b
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_countTrying to unmount old root ... okay
Freeing unused kernel memory: 8k initEXT2-fs: #blocks per group too big: 1678566
4
empeg-car 1.0.