Mark and all, I get the following, and then nothing happens - Ctrl C nor q enter do nothing. I have tried both v.2 final and beta 13.

empeg-car bootstrap v1.02 20001106 ([email protected])
Linux NET4.0 for Linux 2.2
If there is anyone present who wants to uea Universit
Copying kernel...
Calling linux kernel...
IrDA (tm) Protocols f
Uncompressing Linux..................................... done, booting the kernerDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
l.
Linux version 2.2.14-rmk5-np17-empeg51 (mac@aphex) (gcc version 2.95.3 20010315 ( revision:Wed May 26 00:49:11 1999 )
(release)) #16 Wed Jul 24 18:19:54 BST 2002ing kswapd v 1.5
SA110
Processor: Intel StrongARM-1100 revision 11options enabled
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.a SA1100 UART
ttyS01 at
empeg-car player (hardware revision 9, serial number 40103932)

empeg dsp audio init
Dentry hash table entries: 2048 (order 2, 16k)xer initialised
emp
Buffer cache hash table entries: 16384 (order 4, 64k) initialised, CS4231A revision a0
Page cache hash table entries: 4096 (order 2, 16k)nel button initialised.
POSIX conformance testing by UNIFIXlised, PDIUSBD12 id 1012
Linux NET4.0 for Linux 2.2
empeg state support ini
Based upon Swansea University Computer Society NET3.039
empeg RDS d
NET4: Linux TCP/IP 1.0 for NET4.0
empeg power-pic drive
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhas 16 RAM
SA1100 serial driver version 4.27 with no serial options enabled48kB Cache, CHS=58140/16/63
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UARTtialized
smc chip
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART9194.c:v0.12 03/06/96 by Erik Stahlman (erik@vt.
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART

SMC9194: SMC91C94(r:9) at 0x4008000
Signature is 636f6972 'rioc'0:02:d7:28:0f:5
Scheduling custom logo.
empeg display initialised.tition check:
empeg usb initialised, PDIUSBD12 id 1012ktime reached, running e2fsck is recomme
empeg state support initialised 0089/88c1 (save to d0005e00).
VFS: Mounted root (ext2 filesystem).
empeg RDS driver initialisedp v0.03 (19980601)
empeg power-pic driver initialised (first boot)FS: Mounted root (ext2 filesystem) readonly.
RAM disk driver initialized: 16 RAM disks of 4096K size
change_root: old root has d_count=1
empeg single channel IDE
Trying to unmount o
Probing primary interface...
Freei
hda: FUJITSU MHL2300AT, ATA DISK drivenit 0.8
hdb: FUJITSU MHL2300AT, 28615MB w/2048kB Cache, CHS=58140/16/63rst music partition read-only
empeg-flash driver initializedc partition read-only
smc chip id/revision 0x3349
Press 'q' now to go
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected]).
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
hdb: hdb1 < hdb5 hdb6 > hdb2 hdb3 hdb4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
empeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Remounting first music partition read-only
Remounting second music partition read-only
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00-beta13 2002/07/24.
Prolux 4 empeg car - 2.1434 Jul 24 2002
Vcb: 0x4086d000

It seems to hang here.

Whatever you could tell me would be most appreciated

Joe