I'm trying to add a dead laptop hitachi drive, the hd works fine in my new laptop but while following the upgrade guide I get following error message. It seems it has problem reading the partion any has any ideas, could I do somethings more manually to more pinpoint the error.

/nB

e000 v1.04
Copying kernel...12M available (96
Calling linux kernel...
on 2.95.3 20010315 (release)) #130 Mon Oct 22 18:52:07 BST 2001)
If there is
Processor: Intel StrongARM-1100 revision 11
POSIX conformance testing b
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer C
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli).....
empeg-car player (hardware revision 7, serial number 80000427)
Command line: mem=12m: IrCOMM protocol ( r
Calibrating delay loop... 207.67 BogoMIPS
Memory: 10968k/12M available (964k code, 20k
POSIX conformance testing by UNIFIX.5
SA1100 seri
Linux NET4.0 for Linux 2.2 no serial options enabled
Based upon Swansea University Computer Society NET3.039
C
t
NET4: Linux TCP/IP 1.0 for NET4.0a
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 67706d65 'empg'
Scheduling custom logo.
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
Could not find CS4231A (version=00)
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 0000
empeg state support initialised 0089/88c1 (save to d0004100).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
Probing primary interface...
hda: HITACHI_DK23BA-10, ATA DISK drive
hda: HITACHI_DK23BA-10, ATA DISK drive
hda: HITACHI_DK23BA-10, ATA DISK drive
hda: HITACHI_DK23BA-10, ATA DISK d
hda: HITACHI_DK23BA-10, ATA DISK driveialised.cols: ICMP, UDP, TCP
ide0 at 0x000-0x007,0x038 on irq 6
empeg usb in
hda: HITACHI_DK23BA-10, 9590MB w/512kB Cache, CHS=19485/16/63
TCP: Hash tables configured (ehas
empeg-flash driver initializedt initialised 0089/88c1 (save
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])alised.2 (Dag Brattli)

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:10:01:a
ircomm_tty: virtual
ide0 at 0x000-0x007,0x038 on irq 6ed
b
Partition check:
h
hda:hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
SA1100 serial driver version 4.27 wit
hda: read_intr: error=0x04 { DriveStatusError }
hdb: HITACHI_DK23BA-10, 9
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x04 { DriveStatusError }
ide0: reset: success
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error }
hda: read_intr: error=0x04 { DriveStatusError }
end_request: I/O error, dev 03:00 (hda), sector 0
unable to read partition table
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...attempt to access beyond end of device
03:05: rw=0, want=2, limit=0
dev 03:05 blksize=1024 blocknr=1 sector=2 size=1024 count=1
EXT2-fs: unable to read superblock
Kernel panic: VFS: Unable to mount root fs on 03:05