Unoffical empeg BBS

Quick Links: Empeg FAQ | RioCar.Org | Hijack | BigDisk Builder | jEmplode | emphatic
Repairs: Repairs

Topic Options
#275805 - 08/02/2006 17:13 New Drive Blues..
EDub
journeyman

Registered: 23/04/2002
Posts: 51
Ok, I put in a single new 40GB hard drive. Did the Builder & then put on the developer image.

I didn't put HiJack on yet, I'm just trying to make sure it's working. Here's what I got from the serial port:

Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.14-rmk5-np17-empeg52 (rob@aphex) (gcc version 2.95.3 20010315
(release)) #11 Tue Apr 1 18:49:59 BST 2003
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 40104030)
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 206f6972 'rio '
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0005300).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: CSD CAV040H, ATA DISK drive
hda: CSD CAV040H, ATA DISK drive
hda: CSD CAV040H, ATA DISK drive
hda: CSD CAV040H, ATA DISK drive
hda: CSD CAV040H, ATA DISK drive
hda: CSD CAV040H, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: CSD CAV040H, 38154MB w/8192kB Cache, CHS=4864/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:0f:b
e
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
player.cpp : 385:empeg-car 2.00 2003/04/01.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Mar 26 2003
Vcb: 0x4086d000

It won't put songs on the disk even though it can go through the sync. So is this disk mounted as read only?

Top
#275806 - 08/02/2006 17:33 Re: New Drive Blues.. [Re: EDub]
pgrzelak
carpal tunnel

Registered: 15/08/2000
Posts: 4859
Loc: New Jersey, USA
Did emplode crash or fail in any way?
_________________________
Paul Grzelak
200GB with 48MB RAM, Illuminated Buttons and Digital Outputs

Top
#275807 - 08/02/2006 17:36 Re: New Drive Blues.. [Re: pgrzelak]
EDub
journeyman

Registered: 23/04/2002
Posts: 51
Emplode crashes at the rebuild databases part. I'm reading the FAQ about · " I got an error message about 'e2fsck' at the shell prompt. What do I do to fix it?"

Top
#275808 - 08/02/2006 18:23 Re: New Drive Blues.. [Re: EDub]
EDub
journeyman

Registered: 23/04/2002
Posts: 51
Figured it out. The Builder didn't finish the first time. Reapplied it and now things are working.

Top