dear all,
i haven't been here for years now... time simply doesn't allow..
as one of my two disks in my MkII Empeg now starts to fail i got a new diskdrive (Hitachi Travelstar, 100 GB) and i wanted to upgrade my player - at least i wanted to replace the two existing disks (30+40 GB) with the new one.
i followed the instructions of how to upgrade on riocar.org.
- downloaded software (emplode v2.0)
- installed emplode
- downloades emplode new version v2.10
- downloaded disk-builder (old and newer 20011022) for mk II
- downloaded player images (alpha 3.11 and consumer 2.00 - developer)
- run the disk-builder - it seemed to run ok, stresstest was made
- stopped stress test and installed the consumer 2.00, which also didn't come up with any error.
but now i can't connect to the empeg neither with emplode v2.0 nor emplode v2.1.
when connecting it v2.0 comes to the point "checking media", then player reboots and emplode immidately ends.
when connecting with v2.10 i get an error at "checking database" and i can't do anything further.
when i connect with hyperterminal i get following output:
empeg-car bootstrap v1.00 20000601 (
[email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...
empeg-car bootstrap v1.00 20000601 (
[email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!
e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux..................................... done, booting the kernel.
Linux version 2.2.14-rmk5-np17-empeg52 (rob@aphex) (gcc version 2.95.3 20010315 (release)) #11 Tue Apr 1 18:49:59 BST 2003
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 7, serial number 80000143)
Command line: mem=12m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 10968k/12M available (964k code, 20k reserved, 332k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 67706d65 'empg'
Scheduling custom logo.
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initialised
empeg audio-in initialised, CS4231A revision a0
empeg remote control/panel button initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0005600).
empeg RDS driver initialised
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: HTS541010G9AT00, ATA DISK drive
hda: HTS541010G9AT00, ATA DISK drive
hda: HTS541010G9AT00, ATA DISK drive
hda: HTS541010G9AT00, ATA DISK drive
hda: HTS541010G9AT00, ATA DISK drive
hda: HTS541010G9AT00, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: HTS541010G9AT00, 95396MB w/7539kB Cache, CHS=12161/255/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman (
[email protected])
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:10:00:8f
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump..`e5jչѕɽсɁѕɕ)5change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
VFS: Can't find an ext2 filesystem on dev ide0(3,4).
Tried to mount /dev/hda4 as ext2 but got error 22
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
No primary hard disk
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To ComplStarting player
player.cpp : 385:empeg-car 2.00 2003/04/01.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Mar 26 2003
Vcb: 0x4054d000
Vcb: 0
Vcb: 65536
Vcb: 0
Vcb: 65536
q
Restored terminal settings
Remounting first music partition read-only
No primary hard disk
Remounting second music partition read-only
No secondary hard disk
Player exited normally: 0
Switching to shell-player loop
Starting bash.
empeg:/empeg/bin# ls /drive0
empeg:/empeg/bin#
empeg:/empeg/bin# mount
/dev/root on / type ext2 (ro)
none on /proc type proc (rw)
empeg:/empeg/bin#
so to me it seems as if the disk hasn't been formated correctly or cant be mounted or something like this...
could someone give me a hint of how to handle? is the disk maybe too large for the player? (100 GB)
what could i do?
Previous Topic
Index