Ok. What is apparently happening is my Pioneer remote still isn't working except for a couple of buttons that happen to have the same code that you compiled into the kernel.

I rebuilt the player and captured the output for each stage.
Followed Franks instructions again but the time I also added his enabling of the verbose ir output on the serial port.

This is the capture just after the IR only kernel was installed....

empeg-car v0.04 19990121 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux........................ done, booting the kernel.

Linux version 2.2.14-rmk5-np17-empeg49 (mcomb@grovepc) (gcc version 2.95.2 19991024 (release)) #2 Sun Nov 11 17:27:32 PST 2001

Processor: Intel StrongARM-1100 revision 9

NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.

empeg-car player (hardware revision 4, serial number 00102)

Command line: mem=8m

Calibrating delay loop... 207.67 BogoMIPS

Memory: 7316k/8M available (584k code, 20k reserved, 268k data, 4k init)

Dentry hash table entries: 1024 (order 1, 8k)

Buffer cache hash table entries: 8192 (order 3, 32k)

Page cache hash table entries: 2048 (order 1, 8k)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

Starting kswapd v 1.5

SA1100 serial driver version 4.27 with no serial options enabled

ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART

ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART

ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART

Signature is 67706d65 'empg'

Scheduling custom logo.

empeg display initialised.

empeg dsp audio initialised

empeg dsp mixer initialised

empeg dsp initialised

empeg remote control/panel button support initialised (Using FIQs).

AD520B->B94615 11358731->12142101

AD520A->B94614 11358730->12142100

AD5242->B9460A 11358786->12142090

AD5243->B9460B 11358787->12142091

AD5212->B9461B 11358738->12142107

AD521A->B9461F 11358746->12142111

AD520C->B9460E 11358732->12142094

AD5240->B9460D 11358784->12142093

AD5241->B9460C 11358785->12142092

AD521E->B9465E 11358750->12142174

empeg usb initialised, USBN9602 revision 1

empeg state support initialised 0089/8893 (save to d0005900).

empeg RDS driver initialised

empeg power state driver initialised

Linux video capture interface: v1.00

empeg FM radio driver (Philips).

RAM disk driver initialized: 16 RAM disks of 4096K size

empeg dual channel IDE

Probing primary interface...

No drives found, retrying...

No drives found, retrying...

No drives found, retrying...

hda: IBM-DJSA-230, ATA DISK drive

hdc: IBM-DARA-218000, ATA DISK drive

Registering drives...

ide0 at 0x040-0x047,0x078 on irq 7

ide1 at 0x000-0x007,0x038 on irq 6

hda: IBM-DJSA-230, 28615MB w/1874kB Cache, CHS=58140/16/63

hdc: IBM-DARA-218000, 17297MB w/418kB Cache, CHS=37488/15/63

empeg-flash driver initialized

Partition check:

hda: hda1 < hda5 hda6 > hda2 hda3 hda4

hdc: hdc1 < hdc5 hdc6 > hdc2 hdc3 hdc4

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.

VFS: Mounted root (ext2 filesystem).

empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.

change_root: old root has d_count=1

Trying to unmount old root ... okay

Freeing unused kernel memory: 4k initI see this is a developer image!
Mounting proc
Mounting first music partition
Mounting second music partition
Remounting first music partition read-only
Remounting second music partition read-only
Press 'q' now to go into development mode. You Have Zero Seconds To CompStarting player
empeg-car 2.00-beta3 2001/10/17.
Prolux 4 empeg car - 1.860 Oct 17 2001
Vcb: 0x402be000
E !! mp3_decoder.cpp 1052: Failed to seek to offset 2425870, error=0xc0044000


And this is the capture after I installed the map file and new init.

empeg-car v0.04 19990121 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel...
Uncompressing Linux........................ done, booting the kernel.

Linux version 2.2.14-rmk5-np17-empeg49 (mcomb@grovepc) (gcc version 2.95.2 19991024 (release)) #2 Sun Nov 11 17:27:32 PST 2001

Processor: Intel StrongARM-1100 revision 9

NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.

empeg-car player (hardware revision 4, serial number 00102)

Command line: mem=8m

Calibrating delay loop... 207.67 BogoMIPS

Memory: 7316k/8M available (584k code, 20k reserved, 268k data, 4k init)

Dentry hash table entries: 1024 (order 1, 8k)

Buffer cache hash table entries: 8192 (order 3, 32k)

Page cache hash table entries: 2048 (order 1, 8k)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

Starting kswapd v 1.5

SA1100 serial driver version 4.27 with no serial options enabled

ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART

ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART

ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART

Signature is 67706d65 'empg'

Scheduling custom logo.

empeg display initialised.

empeg dsp audio initialised

empeg dsp mixer initialised

empeg dsp initialised

empeg remote control/panel button support initialised (Using FIQs).

AD520B->B94615 11358731->12142101

AD520A->B94614 11358730->12142100

AD5242->B9460A 11358786->12142090

AD5243->B9460B 11358787->12142091

AD5212->B9461B 11358738->12142107

AD521A->B9461F 11358746->12142111

AD520C->B9460E 11358732->12142094

AD5240->B9460D 11358784->12142093

AD5241->B9460C 11358785->12142092

AD521E->B9465E 11358750->12142174

empeg usb initialised, USBN9602 revision 1

empeg state support initialised 0089/8893 (save to d0005980).

empeg RDS driver initialised

empeg power state driver initialised

Linux video capture interface: v1.00

empeg FM radio driver (Philips).

RAM disk driver initialized: 16 RAM disks of 4096K size

empeg dual channel IDE

Probing primary interface...

No drives found, retrying...

No drives found, retrying...

No drives found, retrying...

hda: IBM-DJSA-230, ATA DISK drive

hdc: IBM-DARA-218000, ATA DISK drive

Registering drives...

ide0 at 0x040-0x047,0x078 on irq 7

ide1 at 0x000-0x007,0x038 on irq 6

hda: IBM-DJSA-230, 28615MB w/1874kB Cache, CHS=58140/16/63

hdc: IBM-DARA-218000, 17297MB w/418kB Cache, CHS=37488/15/63

empeg-flash driver initialized

Partition check:

hda: hda1 < hda5 hda6 > hda2 hda3 hda4

hdc: hdc1 < hdc5 hdc6 > hdc2 hdc3 hdc4

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.

VFS: Mounted root (ext2 filesystem).

empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.

change_root: old root has d_count=1

Trying to unmount old root ... okay

Freeing unused kernel memory: 4k initI see this is a developer image!
Mounting proc
Mounting first music partition
Mounting second music partition
Remounting first music partition read-only
Remounting second music partition read-only
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
empeg-car 2.00-beta3 2001/10/17.
Prolux 4 empeg car - 1.860 Oct 17 2001
Vcb: 0x402be000
E !! mp3_decoder.cpp 1052: Failed to seek to offset 829747, error=0xc0044000
E !! mp3_decoder.cpp 1047: Failed to find valid sync after seeking to offset 829747, error=0xc0044000

And this is what it is showing with the verbose reporting...

AD520A -> B94614
AD520A -> not sent
80AD520A -> 80B94614

AD520B -> B94615
AD520B -> not sent
80AD520B -> 80B94615

AD5210 -> AD5210
AD5210 -> AD5210
AD5210 -> AD5210
80AD5210 -> 80AD5210

AD5211 -> AD5211
AD5211 -> AD5211
AD5211 -> AD5211
80AD5211 -> 80AD5211

4 button presses.
Vol +
Vol -
Track +
Track -

The volume happens to be the same codes as my remote but the track buttons aren't.

Apparently it's not reading the ircodes file, maybe because there were already codes compiled in the kernel?

Any ideas?

_________________________
Steve DarkStorm Designs