well, the clean hijack kerne did not help but programmed successful...

here is the actual hypertpaste


empeg-car bootstrap v1.02 20001106 ([email protected])bing primary interface...
r10 = 4001D
If there is anyone present who wants to upgrade the flash, let them speak now,
hda: TOSHIBA MK4018GAS, ATA DISK drive

or forever hold their peace...it seems not. Let fly the Penguins of Linux!F
hda: TOSHIBA MK4018GAS, ATA DISK drive

e000 v1.04SHIBA MK40
Copying kernel...ive00000 r4 = 00
Calling linux kernel...
hda: TOSHIBA MK4018GAS
Uncompressing Linux..................................... done, booting the kerneon irq 6
init(1): memory violation at pc=
hda: TOSHIBA MK4018GAS, 38154MB w/0kB
l.ch
Linux version 2.2.17-rmk5-np17-empeg52-hijack-v395 ([email protected]) (gcc version 2.peg-flash driver initializedr10: 4001d858 r9 : 00000000
smc chip id/revision
95.3 20010315 (release)) #2 Sun Jun 27 17:52:49 EDT 20046 by Erik Stahlman ([email protected])

Processor: Intel StrongARM-1100 rev
init(1): memory viol
Memory: 15016k/16M available (980k code, 20k reserved, 364k data, 4k init)C: 000000157 = 40000230
Dentry hash table entries: 2048 (order 2, 16k)m [<40003998>]20 r4 = 4001E16050>] lr : [<
Buffer cache hash table entries: 16384 (order 4, 64k)
r10
Page cache hash table entries: 4096 (order 2, 16k)00000]p : bff
IP Protocols: ICMP, UDP, TCP
Function entered at
TCP: Hash tables configured (ehash 16384 bhash 16384)f994 r4 = 00000000
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
r10 = 4001D858 r5 = 00000000 r4 =
Starting kswapd v 1.55d35c r4 : 4012cc6c0
SA1100 serial driver version 4.27 with no serial options enabled
Function entered at [<400023e0>] fro
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART0062c r0 : 000
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
r10 = 00000000 r9 = 0000000
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART


empeg dsp initialised
sp : bffff968 ip :
empeg audio-in initialised, CS4231A revision a0
Function entered at [<40002
empeg remote control/panel button initialised.4001d858 r9 : 00000000 r8 : bffff99400
empeg usb initialised, PDIUSBD12 id 1012r10 = 4001D858 r5
r7
empeg state support initialised 0089/88c1 (save to d0004780).
Function
empeg RDS driver initialised

empeg power-pic driver initialised (first boot)1e440 r1 : 0000062c r0 : 0000000c = 00000000
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
r6 = 40

hda: TOSHIBA MK4018GAS, ATA DISK drive000000 r5 = 00000000 r4 = 00000000od
ide0 at 0x000-0x007,0x038 on irq 6
hda: TOSHIBA MK4018GAS, 38154MB w/0kB Cache, CHS=4864/255/630b750, lr=0x4000b738 (bad address=0x8003c660000015
empeg-flash driver initialized
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:18:04:2
0
Partition check:
hda:hda: status timeout: status=0x84
hda: drive not ready for command
ide0: reset timed-out, status=0x84
hda: status timeout: status=0x84
hda: drive not ready for command
ide0: reset timed-out, status=0x84
hda: status timeout: status=0x84
end_request: I/O error, dev 03:00 (hda), sector 0
hda: drive not ready for command
unable to read partition table
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
Timezone: /usr/share/zoneinfo
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...attempt to access beyond end of device
03:05: rw=0, want=2, limit=0
dev 03:05 blksize=1024 blocknr=1 sector=2 size=1024 count=1
EXT2-fs: unable to read superblock
Kernel panic: VFS: Unable to mount root fs on 03:05


what could i try now??

thanx for ur all help! dave