Unoffical empeg BBS

Quick Links: Empeg FAQ | RioCar.Org | Hijack | BigDisk Builder | jEmplode | emphatic
Repairs: Repairs

Topic Options
#279894 - 20/04/2006 19:02 Drive problem
digitalgunfire
new poster

Registered: 29/03/2006
Posts: 10
I just reformatted the player using the upgrade. It hangs on 'finding pump' and fails with 'Couldn't find pump error 0x20'

I ran the developer upgrade and it seemed to take.

However, it hangs at the boot screen and if i hyperterminal in I get tons and tons of this:

EXT2-fs error (device ide0(3,4)): ext2_free_blocks: Freeing blocks not in datazo
ne - block = 2946096496, count = 1
Remounting filesystem read-only
Kernel panic: EXT2-fs panic (device ide0(3,4)): load_block_bitmap: block_group >
= groups_count - block_group = 524287, groups_count = 4757

Any ideas?

Top
#279895 - 20/04/2006 19:44 Re: Drive problem [Re: digitalgunfire]
pgrzelak
carpal tunnel

Registered: 15/08/2000
Posts: 4859
Loc: New Jersey, USA
Can you post a full boot log? You used the upgrader or builder? The upgrader should have only loaded software, not formatted any partitions. Is this a new drive?
_________________________
Paul Grzelak
200GB with 48MB RAM, Illuminated Buttons and Digital Outputs

Top
#279896 - 20/04/2006 20:05 Re: Drive problem [Re: pgrzelak]
digitalgunfire
new poster

Registered: 29/03/2006
Posts: 10
No, it's an old drive.

Here's the story.

I just sold the player so I was going to wipe out all the mp3s on it. My current PC doesn't have a serial port so I figured I'll use emplode to delete all the mp3s.

I delete 'em all and get a few sync errors (I was ripping mp3s and stuff at the same time so I figured it might've been resource problem.)

Then my PC locked up. I rebooted and the player was hanging at the logo. So I figured I'll reformat it. I run the disk builder and it runs fine until it gets to 'Finding pump (preparing first hard disk)'

It runs through this, and then says 'Couldn't find pump - error occured during stage 0x20'

I can still apply the upgrade after this, and it seems to take, but it will either hang at the empeg logo or at 'Building music database'

Here's a complete boot log. This is after I tried the version 3 image just to see if it would change.


Calling linux kernel...
Uncompressing Linux..................................... done, booting the kernel.

Linux version 2.2.14-rmk5-np17-empeg55 (peter@tatu) (gcc version 2.95.3 20010315 (release)) #15 Mon Jul 25 18:52:48 BST 2005

Processor: Intel StrongARM-1100 revision 11

Checking for extra DRAM:

c1000000: wrote ffffffff, read 9afffff0

NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.

empeg-car player (hardware revision 9, serial number 10101694)

Command line: mem=16m

Calibrating delay loop... 207.67 BogoMIPS

Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)

Dentry hash table entries: 2048 (order 2, 16k)

Buffer cache hash table entries: 16384 (order 4, 64k)

Page cache hash table entries: 4096 (order 2, 16k)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.2

Based upon Swansea University Computer Society NET3.039

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

TCP: Hash tables configured (ehash 16384 bhash 16384)

IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)

Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )

ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )

Starting kswapd v 1.5

SA1100 serial driver version 4.27 with no serial options enabled

ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART

ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART

ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART

Signature is 67706d65 'empg'

Scheduling custom logo.

empeg display initialised.

empeg dsp audio initialised

empeg dsp mixer initialised

empeg dsp initialised

empeg audio-in initialised, CS4231A revision a0

empeg remote control/panel button initialised.

empeg usb initialised, PDIUSBD12 id 1012

empeg state support initialised 0089/88c1 (save to d0004280).

empeg RDS driver initialised

empeg power-pic driver initialised (first boot)

RAM disk driver initialized: 16 RAM disks of 4096K size

empeg single channel IDE

Probing primary interface...

hda: FUJITSU MHT2040AT, ATA DISK drive

hda: FUJITSU MHT2040AT, ATA DISK drive

hda: FUJITSU MHT2040AT, ATA DISK drive

hda: FUJITSU MHT2040AT, ATA DISK drive

hda: FUJITSU MHT2040AT, ATA DISK drive

hda: FUJITSU MHT2040AT, ATA DISK drive

ide0 at 0x000-0x007,0x038 on irq 6

hda: FUJITSU MHT2040AT, 38154MB w/2048kB Cache, CHS=4864/255/63

empeg-flash driver initialized

smc chip id/revision 0x3349

smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])


SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:22:06:9e

Partition check:

hda: hda1 < hda5 hda6 > hda2 hda3 hda4

RAMDISK: ext2 filesystem found at block 0

RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.

EXT2-fs warning: checktime reached, running e2fsck is recommended

VFS: Mounted root (ext2 filesystem).

empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.

change_root: old root has d_count=1

Trying to unmount old root ... okay

Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To ComðStarting player
player.cpp : 587:empeg-car 3.00-alpha11 2005/07/25.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1485 Jul 25 2005
Vcb: 0x4073a000
endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

endpoint stall(clear stall on ep5)

endpoint stall(clear stall on ep4)

I think the endpoint stalls are because I tried to connect with emplode, just to see if it would work.

Top
#279897 - 20/04/2006 20:07 Re: Drive problem [Re: digitalgunfire]
digitalgunfire
new poster

Registered: 29/03/2006
Posts: 10
I'm going to go back to 2-developer, just as a test.

Top
#279898 - 20/04/2006 21:08 Re: Drive problem [Re: digitalgunfire]
digitalgunfire
new poster

Registered: 29/03/2006
Posts: 10
Well, it seems to be working now, it will sync over Emplode.. no idea what fixed it tho.

Top
#279899 - 20/04/2006 21:15 Re: Drive problem [Re: digitalgunfire]
pgrzelak
carpal tunnel

Registered: 15/08/2000
Posts: 4859
Loc: New Jersey, USA
Possibly reflashing it.
_________________________
Paul Grzelak
200GB with 48MB RAM, Illuminated Buttons and Digital Outputs

Top
#279900 - 21/04/2006 10:57 Re: Drive problem [Re: digitalgunfire]
mlord
carpal tunnel

Registered: 29/08/2000
Posts: 14491
Loc: Canada
Mmm.. looks like you were using USB for the emplode connection,, USB has issues with windows.

Cheers

Top