Hi,

I pulled the existing two disks (a 10gb and 18GB) out of my Mark II and replaced it with a single Hitachi 80GN unit. I did the exact same process with my Mk2a and had no problems.

Anyway, I build the Mk II with the disk builder image and ran the stress test all night. I then applied version 2.0 end-user. When I ran Emplode to put my music back, emplode crashs with an error after it restarts the player - during the initial read process. I can't get emplode to start.

So I re-image using the disk builder again - and applied the developer image so I could get to the shell prompt and poke around.

A quick examination of the boot log shows that I might have a partition or filesystem error, but my UNIX days are long behind me and I can't figure it out.

Here is the boot log:

-rwxr-xr-x 1 0 0

e000 v1.04Jul 4 20
Copying kernel...
Calling linux kernel...
/dev
-rwxr-xr-x 1
Uncompressing Linux..................................... done, booting the kerne
-rwxr-xr-x 1 0 0 97 Jul 4 2000 rwm
l.
Linux version 2.2.14-rmk5-np17-empeg52 (rob@aphex) (gcc version 2.95.3 20010315 64668 Feb 6 2000 rz
audioin hda h
(release)) #11 Tue Apr 1 18:49:59 BST 2003 47280 Feb 6 2000 sed
Processor: Intel StrongARM-1100 revision 11
lrwxrwxrwx 1 0 220
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
-rwxr-xr-x 1 0 0 14552 Feb 6
empeg-car player (hardware revision 7, serial number 60000022)

POSIX conformance testing by UNIFIX
-rwxr-xr-x 1
Linux NET4.0 for Linux 2.2 Feb 6 2000 tary while d
Based upon Swansea University Computer Society NET3.039----- 1 0 0 34380 Nov 6 1999 tune
NET4: Linux TCP/IP 1.0 for NET4.0find ext2 superblock, trying bac

IP Protocols: ICMP, UDP, TCP 37404 Feb 6 2000 u
TCP: Hash tables configured (ehash 16384 bhas-blo

SA1100 serial driver version 4.27 with no serial options enabled

empeg:/bin#
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
empeg:/bin# pwin# mount
bash: pw: c
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART Killed playerroc (rw)
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART PID TTY TIME CMD an ext2 filesystem o
Signature is ffffffff 'ÿÿÿÿ'0 bash
empeg display initialised.:00 ps bad option, bad sup
empeg dsp audio initialised
empeg:/# pwd
empeg state support initialised 0089/88c1 (save to d0004380). 0 1024 Jul 4 2000 deve2fs
empeg RDS driver initialised
drwxr-xr-x 2 0
empeg power-pic driver initialised (first boot) rwm swapoff umount
RAM disk driver initialized: 16 RAM disks of 4096K size 1999 drive1halt mkdir mount rm rz swap
empeg single channel IDExr-x 4 0 0
Probing primary interface...eg
cp fsck
hda: IC25N080ATMR04-0, ATA DISK drivewxr-xr-x 3 0 0 1
hda: IC25N080ATMR04-0, ATA DISK drive
empeg:/bin# fsck.ext2
ide0 at 0x000-0x007,0x038 on irq 6
hda: IC25N080ATMR04-0, 76319MB w/7884kB Cache, CHS=9729/255/63c repair (no questions)
l
empeg-flash driver initialized 3 Apr 1 2003 sbin -
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected]) 10 Apr 1 2003 swapfile -> ./dev/hda6

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:0c:00:1 0 1024 Apr 13 1999 tmp even if filesystem is marked clean
6
Partition check:
drwxr-xr-x 4
hda: hda1 < hda5 hda6 > hda2 hda3 hda4 usr Be verbose
empeg:/dri
EXT2-fs warning: checktime reached, running e2fsck is recommendede0 not mounted already, or bad option
-L bad_blocks_fi
VFS: Mounted root (ext2 filesystem).
empeg:/# ls drive0
empeg:/bi
empeg-pump v0.03 (19980601)sage: fdisk
empeg:/mnt# ls[
Press Ctrl-A to enter pump...: Mounted root (ext2 filesystem) readonly.for the f
empeg:/sbin# ls
badblocks dd fsck.ext2 i
change_root: old root has d_count=1 sz disk)
Trying to unmount old root ... okaydev
bash df grep in
Freeing unused kernel memory: 4k initempeg init 0.8
or: fdisk /dev/rd/c0d0 or: fdisk /dev/ida
I see this is a developer image! ln mkswap ps rw
Mounting procne2fs
Mounting first music partition /dev/hda
player.cpp : 385:empeg-car 2.00 2003/04/01.
! tags.cpp : 61:Failed to open tags (0xc0041002).
Prolux 4 empeg car - 2.1434 Mar 26 2003
Vcb: 0x4054d000
q
Restored terminal settings
Remounting first music partition read-only
No primary hard disk
Remounting second music partition read-only
No secondary hard disk
Player exited normally: 0
Switching to shell-player loop
Starting bash.
empeg:/empeg/bin# rw
empeg:/empeg/bin# rwm
mount: /drive0 not mounted already, or bad option
empeg:/empeg/bin# ro
mount: /drive0 not mounted already, or bad option
empeg:/empeg/bin# rom
mount: /drive0 not mounted already, or bad option
empeg:/empeg/bin#

For whatever reason it looks like the music partition isn't being mounted.

empeg:/empeg/bin# player &
[1] 32
empeg:/empeg/bin# player.cpp : 385:empeg-car 2.00 2003/04/01.
! tags.cpp : 61:Failed to open tags (0xc0041002).

Thoughts? Suggestions?

Clarke