Thanks for the suggestions. I still haven't been able to connect via FTP, even after disabling passive mode. Unfortunately the FTP client I'm using right now doesn't offer any other controls for that (only a single check box for passive mode).

Here's the kmsg:

Quote:


<4>Linux version 2.2.17-rmk5-np17-empeg52-hijack-v413 ([email protected]) (gcc version 2.95.3 20010315 (release)) #2 Tue Aug 17 18:05:30 EDT 2004
<4>Processor: Intel StrongARM-1100 revision 11
<4>Checking for extra DRAM:
<4>c1000000: wrote ffffffff, read e91ba9f0
<4>NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
<4>empeg-car player (hardware revision 9, serial number 30102542) 16MB DRAM
<4>Command line: mem=16m
<4>Calibrating delay loop... 207.67 BogoMIPS
<4>Memory: 15008k/16M available (984k code, 20k reserved, 368k data, 4k init)
<4>Dentry hash table entries: 2048 (order 2, 16k)
<4>Buffer cache hash table entries: 16384 (order 4, 64k)
<4>Page cache hash table entries: 4096 (order 2, 16k)
<4>POSIX conformance testing by UNIFIX
<6>Linux NET4.0 for Linux 2.2
<6>Based upon Swansea University Computer Society NET3.039
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<4>TCP: Hash tables configured (ehash 16384 bhash 16384)
<6>IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
<4>Starting kswapd v 1.5
<6>SA1100 serial driver version 4.27 with no serial options enabled
<6>ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
<6>ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
<6>ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
<4>Signature is 67706d65 'empg'
<4>Found custom animation at offset 0x9c378
<4>Tuner: loopback=0, ID=-1
<4>Scheduling custom logo.
<4>empeg display initialised.
<4>empeg dsp audio initialised
<4>empeg dsp mixer initialised
<4>empeg dsp initialised
<4>empeg audio-in initialised, CS4231A revision a0
<4>empeg remote control/panel button initialised.
<4>empeg usb initialised, PDIUSBD12 id 1012
<4>empeg state support initialised 0089/88c1 (save to d0005080).
<4>empeg RDS driver initialised
<4>empeg power-pic driver initialised (first boot)
<4>RAM disk driver initialized: 16 RAM disks of 4096K size
<4>empeg single channel IDE
<4>Probing primary interface...
<4>hdb: FUJITSU MHL2300AT, ATA DISK drive
<4>hda: ST9100823A, ATA DISK drive
<4>hdb: FUJITSU MHL2300AT, ATA DISK drive
<4>ide0 at 0x000-0x007,0x038 on irq 6
<6>hda: ST9100823A, 95396MB w/8192kB Cache, CHS=12161/255/63
<6>hdb: FUJITSU MHL2300AT, 28615MB w/2048kB Cache, CHS=58140/16/63
<4>empeg-flash driver initialized
<4>smc chip id/revision 0x3349
<4>smc9194.c:v0.12 03/06/96 by Erik Stahlman ([email protected])
<4>
<4>SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:26:09:ee
<6>Partition check:
<6> hda: hda1 < hda5 hda6 > hda2 hda3 hda4
<6> hdb: hdb1 < hdb5 hdb6 > hdb2 hdb3 hdb4
<5>RAMDISK: ext2 filesystem found at block 0
<5>RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.
<4>EXT2-fs warning: checktime reached, running e2fsck is recommended
<4>VFS: Mounted root (ext2 filesystem).
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>change_root: old root has d_count=1
<5>Trying to unmount old root ... okay
<4>Freeing unused kernel memory: 4k init
<4>Timezone: EST5EDT
<4>Hijack: intercepting config.ini
<4>
<4>hijack: removed menu entry: "Hard Disk Detection"
<4>hijack: removed menu entry: "Serial Port Assignment"
<4>khttpd: listening on port 80
<4>kftpd: listening on port 21
<4>khttpd: open(/favicon.ico) failed, rc=-2
<4>khttpd: open(/favicon.ico) failed, rc=-2