Here is the hyperterminal output from in AC mode if it helps

empeg-car bootstrap v1.02 20001106 ([email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!

e000 v1.04
Copying kernel...
Calling linux kernel..
Uncompressing Linux..................................... done, booting the kerne
l.
Linux version 2.2.17-rmk5-np17-empeg52-hijack-v488 ([email protected]) (gcc version
2.95.3 20010315 (release)) #2 Fri Feb 15 10:29:26 EST 2008
Processor: Intel StrongARM-1100 revision 11
Checking for extra DRAM:
c1000000: wrote ffffffff, read 00000000
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 9, serial number 30103118) 16MB DRAM
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPS
Memory: 15000k/16M available (992k code, 20k reserved, 368k data, 4k init)
Dentry hash table entries: 2048 (order 2, 16k)
Buffer cache hash table entries: 16384 (order 4, 64k)
Page cache hash table entries: 4096 (order 2, 16k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 16384 bhash 16384)
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
Signature is 636f6972 'rioc'
Found custom animation at offset 0x99380
Tuner: loopback=0, ID=-1
show_message("Hijack v488 by Mark Lord")
empeg display initialised.
empeg dsp audio initialised
empeg dsp mixer initialised
empeg dsp initiali
empeg audio-in initialised, CS4231A revision a0ed, the device was in an unknown
empeg remote control/panel button initialised.
Starting kswapd v 1.5
empeg usb initialised, PDIUSBD12 id 1012ed driver
empeg state support initialised 0089/88c1 (save to d0005d00).rred, registers were:
empeg RDS driver initialisedinitialized:
empeg power-pic driver initialised sizeA1100 UART
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg
02 11 e0 59 00 00 03 Error: a SA110
empeg single channel IDE
Pr
Probing primary interface...

Commands leading to t
ide_data_test: wrote 0x0000 read 0xff0000 read 0x0000RT
ide_data_test: wrote 0xffff read 0xff00
ide_d
CR FR SC
ide_data_test: wrote 0xaaaa read 0xaa00d/Feature_Namend cus
ide_data_test: wrote 0x55

SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:26:0c:2
Partition check: initialisedion
e
Partition check:hda5 hda6
hda: hda1 < hda5 hda6 > hda2 hda3 hda4 After command completion occurred, re
RAMDISK: ext2 filesystem found at block 0donly.isk driver initia
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
ER ST SC SN CL CH DH 4096
EXT2-fs warning: checktime reached, run

Freeing unused kernel memory: 4k initempeg init 0.8
I see this is a developer image!
Mounting proc
Mounting first music partition
Tried to mount /dev/hda4 as reiserfs but got error 19
Mounting second music partition
Tried to mount /dev/hdc4 but got error 6
Error mounting partitions (possibly already mounted)
Remounting first music partition read-only
Remounting second music partition read-only
No secondary hard disk
Press 'q' now to go into development mode. You Have Zero Seconds To Comply...
Starting player
Timezone: Atlantic/South_Georgia
Hijack: intercepting config.ini

hijack: removed menu entry: "Serial Port Assignment"
khttpd: listening on port 80
kftpd: listening on port 21
player.cpp : 385:empeg-car 2.01 2004/07/06.
Prolux 4 empeg car - 2.1434 Jul 5 2004
Vcb: 0x4086d000
Dead temp.sensor, status=0x00