Hi, just got the gear for two hours but with the current soft is pretty unstable, the player keeps hanging so I have to power-reset it, or it reboots (just the player soft, not the OS?)
That's happening mainly when I switch tracs or select a new playlist. Here is the serial out:
empeg-car bootstrap v1.00 20000601 (
[email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,
or forever hold their peace...it seems not. Let fly the Penguins of Linux!
Clearing 12Mb of RAM...
Copying kernel...
Calling linux kernel...
Uncompressing Linux................................ done, booting the kernel.
Linux version 2.2.14-rmk5-np17-empeg26 (
[email protected]) (gcc version 2.95.2 19991024 (release)) #492 Thu Jun 29 14:16:23 BST 2000
Processor: Intel StrongARM-1100 revision 11
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.
empeg-car player (hardware revision 7, serial number 60000048)
Command line:
Calibrating delay loop... 208.08 BogoMIPS
Memory: 7072k/8M available (848k code, 20k reserved, 244k data, 8k init)
Dentry hash table entries: 1024 (order 1, 8k)
Buffer cache hash table entries: 8192 (order 3, 32k)
Page cache hash table entries: 2048 (order 1, 8k)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
TCP: Hash tables configured (ehash 8192 bhash 8192)
Starting kswapd v 1.5
SA1100 serial driver version 4.27 with no serial options enabled
ttyS00 at 0xf8010000 (irq = 15) is a SA1100 UART
ttyS01 at 0xf8050000 (irq = 17) is a SA1100 UART
ttyS02 at 0xf8030000 (irq = 16) is a SA1100 UART
empeg display initialised.
empeg dspaudio driver initialized
empeg audio-in initialised, CS4231A revision a0
empeg infra-red support initialised.
empeg usb initialised, PDIUSBD12 id 1012
empeg state support initialised 0089/88c1 (save to d0004780).
empeg power-pic driver initialised (first boot)
RAM disk driver initialized: 16 RAM disks of 4096K size
empeg single channel IDE
Probing primary interface...
hda: IBM-DARA-212000, ATA DISK drive
hda: IBM-DARA-212000, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: IBM-DARA-212000, 11513MB w/418kB Cache, CHS=23392/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman (
[email protected])
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC xxxxxxxxxxxxxxx
Partition check:
hda: hda1 < hda5 hda6 > hda2 hda3 hda4
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\done.
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 8k initempeg-car 0.90 beta11b pre-release.
VM: killing process player
empeg-car 0.90 beta11b pre-release.
Actually, the last two lines are happening (VM: killing....) when the empeg seem to reboot. Most of the time when switching tracks. When it completely hangs, there is no additional output on the serial, I just had to power reset.
Thanks very much, J.
Previous Topic
Index